Gas chromatography P2 – Flashcards

Unlock all answers in this set

Unlock answers
question
What are the properties of injectors?
answer
- sample injected through septum using syringe -> injector at high T so sample immediately vaporizes -> *large* V expansion -> possible sample degradation if injector is too hot
question
Why can't water be used as a solvent for GC?
answer
H2O has large expansion when it is vapourized -> cannot fit into glass liner -> get tailing peaks and poor separation b/c it enters different parts -> gas inlet, split outlet etc so not an instantaneous injection
question
How does a glass wool plug assist injection?
answer
- promotes efficient vaporization of compound - more consistent results on later peaks
question
How does a split injection work?
answer
- concentrated sample is injected, vaporized and some is transferred to column, rest is vented as waste - valve remains open throughout
question
What are the merits of using a split injection?
answer
- higher concentration and neat samples - produce optimal peak shapes and prolongs column lifetime b/c not overloaded - but maybe not enough sample in column
question
How does a splitless injection work? and Grob method
answer
- sample trapped at head of column while venting residual solvent vapour - split valve closed and solvent creates saturated zone at head of column = trap sample components - split valve opened and residual vapor (mostly solvent) swept out vent Grob - temp is 30 - 40 below solvent BP so analyte condenses
question
What are the merits of a splitless injection?
answer
for low [ ]'s low ppm, high ppb but peak shape less resolved for Grob - better peak shape
question
Draw a diagram of the injection port
answer
GO
question
What are properties of capillary columns?
answer
- glass or fused silica tubes - 0.1 - 0.5 mm id, 10 - 60 m length - sample capacity 0.001 to 0.01 uL - high resolution/sensitivity - shorter analysis time (- packed columns for low MW)
question
What are the types of capillary columns?>
answer
Wall-coated open tubular column (WCOT) Support-coated open tubular column (SCOT) Porous-layer open tubular column (PLOT or GSC)
question
What is the structure of a polysiloxane column?
answer
Draw
question
What are the structure of common stationary phases?>
answer
DRAW
question
What is the difference between a polysiloxane and a polyethylene glycol column?
answer
non-polar (DB1) vs polar (Carbowax)
question
What is the difference between DB1, DB5 and HP1?
answer
DB1 - 100% R groups are methyl DB5 - 5% R groups are phenyl, rest are methyl HP1 - 100% R groups are methyl, different manufacturer
question
How do you select the correct GC column?
answer
1 look for established applications - literature, manufacturer 2 choose stationary phase to match analyte polarity - less polar more stable - low bleed "ms" more intert - won't deteriorate w/ temperature - use temp program
question
What are ideal columns for non-polar compounds?
answer
- non-polar cmpds (alkanes) - have dispersive interactions w/ stat phase (ie van der waals) - use non-polar column - greater attractions w/ greater size so BP proportional to tR
question
What are ideal columns for polar compounds?
answer
- polar compounds (alcohols, esters, ketones, aldehydes, COOH) - use intermediate polarity or polar columns (carbowax) - intrxns are dipole, pi-pi, acid-base - separation dtermined by differences in effects of these interactions
question
What are ideal columns for polarisable compounds?
answer
cmpds are alkenes, aromatics - contain C=C or triple C-C bonds -> can have dipole interactions
question
What are the relative polarities of hydrocarbons, esters, ketones, aldehydes, alcohol, carboxylic acids?
answer
hydrocarbons - nonpolar esters, ketones, aldehydes - weak intermediate polarity alcohol, carboxylic acids - strong intermediate polarity
question
What is the difference between an isothermal temperature and a temperature program?
answer
isothermal: T is constant, 2< k < 10; some analytes not resolved or very broad temperature program starts off at a low temperature then gradually increases temperature - shorter run times, faster elution, better resolution of later peaks, optimized separation
question
Why is changing the temperature of the run not always predictable?
answer
Compound elution may be independent of temperature. ie benzene holds on tighter to column so elution not affected by temp but butanol is not as attracted to column so inc temp = dec tR
question
What is the effect of column diameter on separation?
answer
smaller diameter: increase efficiency, resolution, pressure but decreases capacity, flow rate
question
What is the effect of column length on separation?
answer
longer length: increase efficiency, resolution, analysis time, pressure, cost
question
What is the effect of column film thickness on separation?
answer
thicker film: increase retention, resolution (k5), efficiency
question
What is the phase ratio (beta)?
answer
allows us to predict relationship based on column diameter and film thickness Kc / k = i.d / 4*df
question
What happens when column length changes but phase ratio stays constant? Why would this be done?
answer
shorter run time but separation is identical b/c beta is unchanged - get benefits of changing parameters while keeping phase ratio constant
question
What does the detector achieve?
answer
- produce a stable electronic signal (baseline) when pure carrier gas is in detector - respond rapidly to produce diff signal when component passes through - samples enough to detect sharp peaks - good linear response desired - peak area corresponds to [ ] - wide range of analyte response - detect many compounds
question
How does flame ionization detector (FID) work?
answer
effluent from column passes into air-H2 flame - sample burns and forms ions and e- - conduct elec b/w 2 electrodes -> amount of current = amount of compound - measure current - sensitive for most compounds except gases like CO2, H2O
question
How does thermal conductivity detector work?
answer
detects compounds w/ thermal conductivity that differs from carrier gas
question
How does electron capture detector work?
answer
detects e- - capturing cmpds
question
How does nitrogen-phosphorus detector work?
answer
detects cmpds that contain nitrogen and phosphorus
question
How does atomic emission detector work?
answer
tunable to many elements
question
How does mass selective detector work?
answer
identifies components from mass spectra
Get an explanation on any task
Get unstuck with the help of our AI assistant in seconds
New